Hello again Youmin,
Unfortunately, I am not an expert on the chemistry of the ALEG 380. I do
not know how it works...
I just remember very vividly that I used ALEG 380 for a 8-10 hours long
process to remove a big chunk of BOSCH process polymer from a specific
region while the rest of the wafer was also exposed to ALEG 380. I worked
with SOI wafer. When I used ALGE 380, silicon dioxide surfaces (BOX), and
"silicon device layer" surfaces were exposed ALEG 380. I do not remember
oxide or Si being etched in the end of 8-10 hours long polymer removal
session at 80 degrees Celcius.
Regards,
Mehmet
On Mon, Dec 14, 2015 at 7:39 PM, Youmin Wang
wrote:
> Hello Mehmet,
>
> Thank you very much for your suggestions!!
>
> I have worked with EKC270 from DuPont:
>
> http://www.dupont.com/content/dam/assets/products-and-services/electronic-
electrical-materials/assets/EKC/EKC270.pdf
>
> I think they both remove the polymer and try to "lift off" the residue by
> etching the substrate slightly? Thanks in advance for your comments.
>
>
> Best,
> Youmin
>
> On Mon, Dec 14, 2015 at 9:28 AM, Mehmet Yilmaz
> wrote:
>
>> Dear Youmin,
>> You may try ALEG 380. The link for the product is below:
>>
>> http://www.avantormaterials.com/Electronic-Materials/Markets-and-Applications
/Semiconductor-Chemicals/Post-Etch-Residue-Removal.aspx
>>
>> I used ALEG 380 at 80 degress Celcius temperature. And it definitely
>> worked in my case. However, I see that your features are way more smaller
>> than what I had when I used ALEG 380. My lines and spaces were 2um/2um.
>>
>> I hope this helps! Good luck!
>>
>> Bests,
>>
>> Mehmet
>>
>> On Sun, Dec 13, 2015 at 9:32 PM, Youmin Wang
>> wrote:
>>
>>> Hello Everyone,
>>>
>>> I want to etch the silicon structure below to half of its heigh (from
>>> 2un to 1um) in standard BOSCH process:
>>>
>>> [image: Inline image 1]
>>>
>>> However I got a lot of sidewalls un-removed:
>>>
>>> [image: Inline image 2]
>>>
>>>
>>> I tried with EKC270 post-etch cleaning but there are still quite a few
>>> sidewalls still there, topview is like:
>>>
>>> [image: Inline image 3]
>>>
>>> Do you think whether my etching recipe has any problem, or you know
>>> whether I can do something post-etch to clean those standing sidewalls?
>>> Thanks a lot!
>>>
>>>
>>>
>>> Best,
>>> Youmin
>>>
>>>
>>>
>>> _______________________________________________
>>> Hosted by the MEMS and Nanotechnology Exchange, the country's leading
>>> provider of MEMS and Nanotechnology design and fabrication services.
>>> Visit us at http://www.mems-exchange.org
>>>
>>> Want to advertise to this community? See http://www.memsnet.org
>>>
>>> To unsubscribe:
>>> http://mail.mems-exchange.org/mailman/listinfo/mems-talk
>>>
>>>
>>
>
PNG
IHDR ä + §
IDATxtÝÉ]Eá*fbfÍ%¶ðn<-æ¹Û¾´ûËÜ©Ã,ÉÌ8çÞ*©éîG_|ñÅÿý÷ßÝýýýÝ
/¼p÷×_Ýýý÷ßwìÑ£Gw/¾øâx~çÿý÷,g8ÆWÜþøñã³þüóÏQ÷?ÿüsüvK¾]ýêÉ
wHo|ê¥_®&^m5ÝY<8Í@/O<¹ûõ×_ï~ÿý÷ÇÄéHS½âã
³ÌÕ®®8~¾´í¹¾ùÒå.¶z >ZÅá÷yɳ^ãp§_¾îÎÞw\õÔ]¾:pé«>
ß¹{5Õgj¬óö'géU
?ñµc¾pníôÛZÅðZå¥Þ
>ø:ëÁõÙpW#n;¸Í«xþêô¬ât·âw6ZªONïaoq1
ÇY¿bÎøðãÐ
Lyü¬»^gx`¬ú
S÷ºÂUGn}WgkÀ]-Îðqâ«OwzÄù½¿|z5+ß!¬ç
þ«®Õ
Wf¢<zî=·8åywö®~úñ¦É^m|îÛÃÞÝ=ãL¯}}ê»ãöÌû\˧߽ïWß
üÌ®'qÖüðå3[¦&ÝÕâS³ï
ßñõ¥¦Xy»W
ÏN<÷f#Lþú Sßoü°üað¸×~ýÛûí·g³¡ÁÝl{Ö´ê[¾
g¹´àn
鮶ú0rÊ3kîLÅê©W¿òébò|xÊmß8_ÚùñYL,NúºiïHw>g~uÝÓ¡|qg|fdü×þÝå7KßxiL
ÍN¼0jãN§g]?0bõW,-ü8ðÑ×SÚý>ßïrOGþù@ Ö¾ × ±jÚî.^3åÚùÅ